×

You are using an outdated browser Internet Explorer. It does not support some functions of the site.

Recommend that you install one of the following browsers: Firefox, Opera or Chrome.

Contacts:

+7 961 270-60-01
ivdon3@bk.ru

  • Programming the robot controller to implement the technological process of laser cutting

    Stepper motors are often used in automated laser cutting systems. The control circuit of a stepper motor requires a special electronic device - a driver, which receives logical signals as input and changes the current in the motor windings to provide motion parameters. This research study evaluated stepper motor drivers to determine the feasibility of their use - PLDS880, OSM-42RA, OSM-88RA. To control the system, software code was written, which was connected to the controller via a link board. With each driver, in different modes, optimal parameters were selected (initial speed, final speed and acceleration), that is, the movement of the carriage without stalling for ten passes with a minimum travel time. The results of the experiments are presented in the form of tables.

    Keywords: laser, laser cutting, automation, technological process, stepper motor, performance, driver, controller, control circuit, optimal parameters

  • Programming the robot controller to implement the technological process of laser cutting

    Stepper motors are often used in automated laser cutting systems. The control circuit of a stepper motor requires a special electronic device - a driver, which receives logical signals as input and changes the current in the motor windings to provide motion parameters. This research study evaluated stepper motor drivers to determine the feasibility of their use - PLDS880, OSM-42RA, OSM-88RA. To control the system, software code was written, which was connected to the controller via a link board. With each driver, in different modes, optimal parameters were selected (initial speed, final speed and acceleration), that is, the movement of the carriage without stalling for ten passes with a minimum travel time. The results of the experiments are presented in the form of tables.

    Keywords: laser, laser cutting, automation, technological process, stepper motor, performance, driver, controller, control circuit, optimal parameters

  • Exploring the possibilities of the Python programming language for creating intelligent baggage scanning systems

    This study is devoted to analyzing the capabilities of the Python programming language when creating information systems for detecting dangerous objects in luggage. As a result, a recognition system architecture was developed, including the following main components: an image processing module, a machine learning module, a database and a user interface. The software chosen is Python with the libraries PySide6, SQLite, Numpy, YOLO. The information system was implemented and tested on real data, which confirmed the correctness of the selected capabilities and technologies of the Python language for the development of security information systems.

    Keywords: information system, security, neural network, machine learning, pattern recognition, performance

  • Application of machine learning and natural language processing to develop a recommendation system for the selection of perfumery products

    The paper discusses the use of machine learning in relation to natural language processing (sentiment analysis, semantic proximity analysis) to build a recommendation system for the choice of perfumery products. The topic of the work is relevant in view of the growth of the range of manufactured perfumery products and the complexity of its choice by consumers and promotion by manufacturers. The proposed approaches are relevant for solving this problem due to the accumulated textual reviews and reviews of perfumery products on various websites, including online stores.

    Keywords: machine learning, natural language, sentiment analysis, distributive semantics, word2vec, recommender systems

  • Air quality monitoring for building environmentally friendly routes

    Many sources of environmental pollution affect human health. The concentration of harmful substances constantly changes during the day when the weather conditions change in different parts of the territory. Residents can repeatedly enter and leave areas of increased pollution without noticing it with their senses when moving around the city. The authors analyzed the existing solutions for monitoring the quality of atmospheric air, as well as key sources of pollution and their distribution in the air. The interrelation of distribution of pollutants with weather conditions is noted. Preparation of data on the presence of harmful substances on the example of the city of Volgograd has been carried out. A method for organizing monitoring of harmful substances in the atmosphere using a software and hardware complex is proposed. The developed method was applied to create a specialized web application. The implemented solution allows to monitor the state of the environment using sensors and build routes around areas with a high concentration of harmful substances.

    Keywords: environment, air quality, air pollution, ecology, monitoring, web application, eco-route, spatial data, route building, cartographic visualization

  • Development of a system for monitoring and preventing accidents at the construction site

    The construction industry is considered to be one of the most unsafe industries, and as a result, safety in the construction industry is considered a very important factor. To reduce the number of accidents and monitor workers at a construction site, the article suggests integrating new tracking and communication technologies. The authors analyze the existing similar technological solutions, identify their advantages and disadvantages. A method for organizing monitoring of workers at a construction site using mobile devices is proposed, as well as the architecture of a software and hardware complex. The developed method is a smart system for a mobile device. This solution allows you to monitor the location of workers using a GPS tracker and a built-in accelerometer, and, if necessary, notify them of a possible danger.

    Keywords: construction site, accidents, safety in construction, employee monitoring, mobile application, geolocation

  • Сonsederation of options for the application of ceramzite gravel in the construction of oil deposisits

    The analysis is made of the use of expanded clay gravel in cement-sand mortar in order to reduce ice at the boundary between the pile and the mortar. The application of expanded clay concrete in block-modular buildings is considered. Lightweight design and reduced heatloss are proven.

    Keywords: diversification of management, production diversification, financial and economic purposes of a diversification, technological purposes of ensuring flexibility of production

  • Synchronization in Direct Sequence Spread Spectrum Systems

    The article conentrates on the problem of synchronization the pseudo-noise sequence in direct sequence spread spectrum systems. Authors propose a method for transmitting information and synchronizing signals on a single carrier frequency, which allows data transmission in complex coditions in radio channel. A brief review of existing solutions for time synchronization direct sequence spread spectrum systems is carried out. The proposed solution is considered in terms of data transmission in broadband systems in the conditions of negative signal-to-noise ratio, while the limitations of the usage of this solution are also considered. A simulation of the scheme that implements the proposed synchronization method is carried out, and the requirements for the signal-to-noise ratio in the information and synchronization channels are determined. The proposed method can find application in systems with code division multiplexing, including modern IoT systems.

    Keywords: time synchronization, direct sequence spread spectrum, broadband communication systems, Internet of Things, BER

  • Experimental studies of combustion of solid fuel in a low-power boiler with a furnace of a high-temperature fluidized bed with recirculation of outgoing gases in static and dynamic modes of operation

    the article presents experimental studies of a low-power boiler with a furnace of a high-temperature fluidized bed with recirculation of outgoing gases in stationary and transient modes of operation. The experimental installation of the boiler KVP-1,74 WKS with recirculation of outgoing gases is represented and described. The results of experimental studies of the dependences of the coefficient of excess oxygen at of the volume of the recirculation of exhaust gases of the boiler KVP-1,74 VTX at nominal and partial loads, based on the percentage of fuel saving of the boiler from the amount of recirculation of exhaust gases of the boiler KVP-1,74 VTX at nominal and partial loads boilers, graphs of transient processes in boiler "KVP-1,74-VTX" with recirculation of flue gas when changing the fuel consumption, GRAPHS of the comparison of transients in the boiler "KVP-1,74-VTX" with recirculation of flue gas when changing fuel consumption.

    Keywords: high temperature fluidized bed, exhaust gas recirculation, experimental studies, automation system

  • Estimation of geomechanical terms and condition of long workings mines of "DTEK Pavlogradugol" development perspective underground mining

    The purpose of research, which are given in the article, is detailed analysis of the existent state of complex of the long workings and development perspective underground mining of Private stock company Pavlogradugol', estimation of total expenses on construction and maintenance of working taking into account repairs, estimation of condition complexity for the development of coal seams on the mines of Western Donbass. Methodical basis of the carried out complex researches is as follows: an analysis and generalization of literary sources and positive experience of maintenance of workings in difficult conditions; methods of mine visual inspections; methods of statistical, valuation, and analytical evaluation of the data on the state of the extended working and complexity of the conditions of development; a comparative analysis of the results achieved. The results of researches are as follows: generalized indexes of workovers on the mines of production amalgamation and separate groups of working; selected group of mines, referred to the category of “large” depth of development; dependence of the length of the workings of the unsatisfactory state on the development condition indicator, obtained from the results of analytical calculations; ways of increasing the stability of extended mine workings of Private stock company DTEK Pavlogradugol'. The got dependences allow determining possible expenses on repair and maintenance of workings in the operating state on the stage of planning. Effective for the examined mining and geological conditions the ways of improvement of support and methods of increase the stability of the long workings are grounded.

    Keywords: long workings, stability, deep mine, expenses on maintenance, methods of maintenance

  • Acoustic method monitoring electrochemical processes

    The article describes the research of thermodurability of glass-carbon - one of the most promising carbon materials used in the production of luminophors and semiconductor materials, optical single crystals, etc. The aim of this work was to study the behavior glass-carbon in the course of thermo-cyclic testing. As a method of diagnostics of the birth and development of micro-cracks was used by the reception of signals of acoustic emission. It is shown that at heating in the samples glass-carbon there was a strong movement of dislocations in thermocyclic effects ,recognized in the signals of acoustic emission. As the number of pulses when heated above, than during the cooling of the sample, it is evidence of the accumulation of damages in the structure of the cyclic thermal processing glass-carbon samples. It is established, that the curves of the accumulation of defects at the pulses of acoustic emission, differ on the stage of heating and cooling. Proposed to use the curve of the aggregate accounts of acoustic emission pulses as a possible harbinger of destruction when heated glass-carbon of the product.

    Keywords: acoustic emission, electrodeposition, the activity of the AE, the remote control.

  • Abstracts

    `

    Keywords: